Bilimsel Çalışmalar


  • NANO-SCALE PROTECTIVE OXIDE FILMS FOR SEMICONDUCTOR APPLICATIONS & BEYOND

    Nano-Scale Protective Oxide Films for Semiconductor Applications & Beyond

    Control of film growth and properties using oxidizers, surface active agents, salts, etc’ in turn will lead to optimized process conditions with improved defectivity and reliability of the current semiconductor manufacturing. 

    Introduction to nano-scale protective thin films and their applications in semiconductor manufacturing, interdisciplinary and multidisciplinary aspect and technological quality. Industrial Technologies 2014 conference on nanotechnologies, biotechnology, advanced materials and new production technologies. 

    Pdf Görüntüle (PDF, 3 kB)    

  • BIOMEDICAL APPLICATIONS OF CHEMICAL MECHANICAL POLISHING ON DENTAL AND PROSTHETIC IMPLANTS

    Biomedical Applications of Chemical Mechanical Polishing on Dental and Prosthetic Implants

    2013 MRS Euro Nano Forum, June 18-20, Dublin, Ireland.

    Control the bio-compatibility and infection resistance of implantable materials through control of surface roughness induced by Chemical Mechanical Planarization (CMP) 

    Pdf Görüntüle (PDF, 2 kB)    

  • MTS CELL PROLIFERATION ASSAY

    MTS Cell Proliferation Assay

    MTS CELL PROLIFERATION ASSAY was performed by Yeditepe University Department of Genetics and Bioengineering. Rat bone marrow stem cell culture was performed for 3 days on the implants which were sent to our laboratory by Mode Medikal San. Tic. Ltd. Sti.

    In MTS Cell Proliferation Assay, sand blasted surface of implants which were manufactured by Mode Medikal  were performed cell proliferation for 23.3% more compared to untreated polished titanium surface.

     

    Pdf Görüntüle (PDF, 0 kB)    

  • DYNAMIC FATIGUE TEST FOR ENDOSSEOUS DENTAL IMPLANTS

    Dynamic fatigue test for endosseous dental implants

    Dynamic Fatigue Test for Endosseous Dental Implants was performed in the labarotory of TOBB University of Economics and Technology which has ISO 14801 standards.

    By Dynamic Fatigue Test, it was reported that implants are not deformed at 360N load. 

    According to test results, specimens were survived under 360 N force and 3,6 Nm bending moment at pre-declared loading conditions. 

    Pdf Görüntüle (PDF, 0 kB)    

  • TORSION TEST OF IMPLANT / BODY CONNECTION

    Torsion Test of Implant / Body Connection

    ISO/TS 13498:2011 establishes a method to determine the torsional yield strength and maximum torque of the implant body/connecting part joints of endosseous dental implant systems. This test is most appropriate for evaluating new types of joints and connecting parts, as well as new materials.

    Torsion Test of Implant/Body Connecting Part Joints of Endosseous Dental Implant System was made by TOBB University of Economics and Technology. According to the test report, it has been observed that the implants haven’t changed their shapes up to 119,8 Ncm load.

    Pdf Görüntüle (PDF, 0 kB)    

  • SELF-PROTECTIVE OXIDE NANO-COATINGS FOR ENHANCED SURFACE BIOCOMPATIBILITY OF TITANIUM

    Self-protective Oxide Nano-Coatings for Enhanced Surface Biocompatibility of Titanium

    National Institute for Laser, Plasma and Radiation Physics, Romania

    The biocompatibility of an implant material depends on the bulk physical properties in addition to the surface properties. In biomedical engineering and industry Ti and Ti-alloys are very popular biological implant material for their bulk physical properties and strength to weight ratio resembling those of nature bone.

    Pdf Görüntüle (PDF, 0 kB)    

  • DEVELOPMENT OF 3-D CHEMICAL MECHANICAL POLISHING PROCESS FOR NANOSTRUCTURING OF BIOIMPLANT SURFACES

    Development of 3-D Chemical Mechanical Polishing Process for Nanostructuring of Bioimplant Surfaces

    This study focuses on the development of a three dimensional chemical mechanical polishing (CMP) process to induce
    smoothness or controlled nano-roughness on the bio-implant material surfaces, particularly for an application on the dental
    implants.

    10.1149/06117.0021ecst ©The Electrochemical Society

    Pdf Görüntüle (PDF, 0 kB)    

  • JOURNAL OF THE INTERNATIONAL MEASUREMENT CONFEDERATION (IMEKO)

    Journal of the International Measurement Confederation (IMEKO)

    Measurement of temperature change during the implant site preparation to determine influence of tool characteristics. In this experimental study drill tip geometry, drill tip angle and drill sharpness affects on procedure temperature were investigated. Experiments were carried on fresh bovine bones and implant sites were prepared individually for each experimental set. Temperature measurement; Bone drilling; Drill tip angle; Osteonecrosis    journal homepage: www.elsevier.com/locate/measurement

    Pdf Görüntüle (PDF, 0 kB)    

  • IMPORTANCE OF MEASUREMENT PARAMETERS FOR THE DENTAL IMPLANT SURFACE CHARACTERIZATION

    Importance of Measurement Parameters for the Dental Implant Surface Characterization

    There are many dierent surface modication techniques like sand blasting, acid etching, or coating with various materials. Surface characterization is as important as surface modication for dental implants. Although many researchers studied about measurement of surface characteristics of dental implants with similar techniques but with dierent measurement parameters, there is still no consensus about the optimal surface characteristics values of a successful dental implant. Among many other surface characteristics, surface roughness is one of the
    most important features for dental implants.

    In this study, the importance of surface roughness measurement of dental implants is discussed and the need of a standardized procedure for implant surface roughness measurement is emphasized. Department of Interchangeable Manufacturing and Industrial Metrology, Institute for Production Engineering and Laser Technology, Vienna University of Technology, Karlspl. 13/3113, A-1040 Wien, Austria

    Pdf Görüntüle (PDF, 0 kB)    

  • IMPLANT SURFACE R&D PROJECT RESULTS

    Implant Surface R&D Project Results

    TUBITAK THE SCIENTIFIC AND TECHNOLOGICAL RESEARCH COUNCIL OF TURKEY

    Tubitak R&D project for “Development of dental implants with increased osseointegration effect by influencing of calcium phosphate on the surface through the method of surface etching and electrolysis application” was successfully completed.
    Homogeneous surface structure was developed by applying optimum calcium and phosphate ions on the surface which accelerate osseointegration process.

    Pdf Görüntüle (PDF, 0 kB)    

  • COMPARISON OF IMPLANT – ABUTMENT BREAKING VALUES

    Comparison of Implant – Abutment Breaking Values

    Comparison of Implant – Abutment Breaking Values. T.C. Yeditepe University  Health  Sciences  Institute  Prosthetic  Dentistry,  Istanbul,  2014. 

    This subject’s aim is to see the breaking values of the implants and abutments and compare them. Totally 40 implants, abutmetns and screws are divided into 4 different groups. ISO14801 standard is used and implants are placed with 30 degree angle to transition piece. 25N torque moment is calibrated by using the company’s implant devices. Instron Universal test machine applied an increasing force until the breaking happens with the speed of 8mm per second.  This process is applied to 40 implants one by one. Breaking values and breaking spotsa resaved. Datas are statistically evaluated by using student test and oneway anova test. Wide platform  diameter  abutments mean breaking value (1753 N) is higher than Regular platform diameter abutments (1685 N).  Keywords: Dental implant, abutment fracture, ISO 14801. 

    Pdf Görüntüle (PDF, 0 kB)